Brands & Models

ShoreStation vs ShoreMaster Boat Lift

Quick answer

The two brands match closely on a small manual lift, but they split above 4,000 lb. ShoreStation's listed lifts above that weight are all hydraulic, with one cylinder that pulls cables and a DC battery charged by solar or a Battery Tender. ShoreMaster keeps a cable winch lift to 7,000 lb that takes a 120 V AC or 12/24 V DC motor, and adds two hydraulic lines, one of them with no cables at all. Pick ShoreStation for beams that need more than 132 in or for the longer cable warranty; pick ShoreMaster for a cable lift with an AC motor or a cable-free hydraulic.

On this page
  1. What is being compared
  2. The spec table
  3. Where they actually differ
  4. Worked example: one boat, two dealers
  5. Which to buy: a rule by depth, weight and dock power
  6. Dealers and who owns each brand
  7. What this comparison does not cover
  8. Frequently asked questions
  9. Sources and further reading

ShoreStation and ShoreMaster match closely on a 4,000 lb manual lift and split above it. ShoreStation's listed lifts are all hydraulic from there up, and all run on a DC battery. ShoreMaster still sells a hand-wheel cable lift up to 7,000 lb that can take a plug-in 120 V motor. It also sells two hydraulic lines, one with no cables at all.

So the forum line that the two are "very similar" is true for small manual lifts and wrong for most of what dealers sell today. It persists because both build aluminum lake lifts, both sell through dock dealers, and both give 15 years on the frame. The table sets the specs side by side, and the sections after it name the six places they differ.

  • Under 4,000 lb: either brand; both sell manual cable lifts at 108 or 120 in wide
  • 4,000 to 7,000 lb with a cable winch or a 120 V AC motor: ShoreMaster (DVS, 66 in travel)
  • Beam needing more than 132 in, or a 15-year cable warranty: ShoreStation hydraulic (to 15,000 lb and 144 in)
  • No cables at all: ShoreMaster cantilever hydraulic, 6,000 to 12,000 lb
  • No power at the dock: either; both brands' hydraulics run on a battery with solar

Independence note: Boat Lift Lab is independent and not affiliated with ShoreStation, ShoreMaster or their dealers. Figures come from the makers' own pages and documents, read in November 2026.

What is being compared

Both brands are best known for free-standing lifts. A free-standing lift is a frame on four adjustable legs. Its foot pads rest on the lake bottom, so it needs no pilings and can come out each fall. The boat sits on a cradle, and the drive raises it. The drive is where these brands part ways.

Three drive types matter here:

  • Cable winch: a hand wheel or motor turns a drum, and steel cables run over pulleys to lift the cradle. The pulleys are called sheaves.
  • Hydraulic with cables: a pump pushes oil into a cylinder. The cylinder pulls the cables, so no drum winds them.
  • Hydraulic without cables: the cylinders push the cradle arms directly. On ShoreMaster's version the cradle swings up in an arc, which makes it a cantilever lift.

Two more terms run through every spec sheet. Travel is how far the cradle moves from fully down to fully up. Inside width is the clear space between the uprights, and it sets the widest hull that fits.

The spec table

ShoreStation vs ShoreMaster free-standing lifts, from the makers' spec pages and documents (November 2026)
SpecShoreStationShoreMaster
Manual cable lifts2,000 lb (100 in) and 3,000 to 4,000 lb (108 or 120 in), 48 in travelDVS vertical 3,000 to 7,000 lb (108 or 120 in), 66 in travel; pontoon lifts 4,000 to 7,000 lb
Hydraulic lifts2,000 to 15,000 lb, inside width 100 to 144 in, cylinder pulls cablesCantilever hydraulic 6,000 to 12,000 lb (108 to 132 in), no cables; vertical hydraulic 4,000 to 15,000 lb (120 or 132 in), with cables
Hydraulic travel48 in (2,000 to 5,000 lb), 54 in (6,000 and 7,000), 64 in (8,000 and 10,000), 70 in (15,000)Cantilever 48 or 60 in; vertical hydraulic 66 in (4,000 to 6,000), 68 in (7,000 and 8,000), 70 in (10,000 to 15,000)
FrameAluminum, bolted together from a kit; galvanized steel cradle tubes from 8,000 lb upWelded aluminum frames with through-bolted connections
Cables and sheavesStainless steel cables; GAR-MAX bushings; manual winch has a grooved drumStainless cables and bushings; solid brass sheaves, 3.5 in (side) and 3.75 in (front and rear) on the DVS; greaseable pulleys on the vertical hydraulic
PowerHydraulic runs on a 12 V or 24 V DC battery; solar panel or a plug-in Battery Tender recharges itHydraulics on a 12 V group 27 battery (buyer supplies it), solar optional; cable lifts take a LiftBoss motor in 120 V AC or 12/24 V DC
Where the pump sitsAluminum box on the lift tube or on the dock, kept above the waterCorrosion-resistant housing; dock mounting with hose extensions is an option
Stopping at the topUpper limit switch; pump pressure regulated so it stalls on an overloadVertical hydraulic has no limit switch; it stops at the end of the cylinder stroke
Frame warranty15 years on structure15 years parts, 3 years labor (residential)
Cable warranty15 years12 years on vertical hydraulic cables
Other parts2-year basic warranty on every Midwest-supplied part, parts and labor (dealer copy)Hydraulic ram and pump 3 years parts, 2 labor; components and accessories 2 years parts, 1 labor; LiftBoss Gen 6 motor 3 years
Salt water or commercial useNot stated in the pages readEverything drops to 1 year; anodes required in brackish or salt water
CanopyREVOLUTION and Legacy covers, ShoreScreen power curtain; fabric warranty 5 yearsTwo frame styles, three fabrics; covers 5 years pro-rated
OwnerMidwest Industries, Inc., Ida Grove, IowaShoreMaster, LLC, Fergus Falls, Minnesota, part of Waterfront Brands

ShoreMaster's hydraulic page says 12,500 lb in one line of copy, but no model in its spec table carries that rating. The table and the brand's overview both stop at 12,000, so this page uses 12,000.

Where they actually differ

1. Above 4,000 lb, ShoreStation is hydraulic and ShoreMaster still offers a cable winch

ShoreStation's capacity page lists manual winch lifts only at 2,000 to 4,000 lb. Every heavier lift on that page is hydraulic. ShoreMaster's DVS cable lift runs from 3,000 to 7,000 lb, with a Whisper Winch hand wheel as standard. Its pontoon lifts cover 4,000 to 7,000 lb the same way. The DVS runs stainless cables over solid brass sheaves, 3.5 in on the sides and 3.75 in front and rear. ShoreStation's manual winch also uses stainless cable, on a grooved drum. So a 5,500 lb boat that wants a plain cable lift has to go to ShoreMaster. The trade-offs between the two drive types are in hydraulic vs cable boat lifts.

2. The hydraulics work in different ways

In a ShoreStation hydraulic lift, the cylinder sits inside one lift tube. Its assembly manual has the cables run from pulleys on that tube down to the cradle tubes. ShoreStation calls this cables "pulled instead of wound": no drum, but the cables are still there and still wear. An upper limit switch stops the cradle at the top. The pump is pressure regulated, so it stalls before it lifts a load that could do damage. The pump and battery sit in an aluminum box on the lift tube or on the dock, which keeps them "high and dry" above the water.

ShoreMaster sells two designs. Its cantilever hydraulic lift has "no cables, no pulleys," and lifts at about 1 inch a second. Its vertical hydraulic lift does use cables, over greaseable pulleys. It has no limit switch: the lift stops when the cylinder reaches the end of its stroke, and the pump changes tone. Its pump sits in a corrosion-resistant housing, and hose extensions let it mount on the dock instead. So ask which "ShoreMaster hydraulic" a quote means. Pulley wear itself is covered in pulleys and sheaves.

3. ShoreStation hydraulics are DC by design

ShoreStation says its hydraulic system "eliminates the need for an AC circuit on the dock." The pump runs from a 12 V or 24 V battery bank. A solar panel or a Battery Tender keeps it charged, and the Tender plugs into a 110 V outlet near the lift. So AC at the dock only charges the battery. ShoreStation's FAQ says a full battery gives 6 to 8 cycles and lasts 3 to 5 years.

ShoreMaster's hydraulics are DC too, on a 12 V group 27 battery with at least 500 cold cranking amps. The difference is its cable lifts. A LiftBoss motor for those comes in 120 V AC or 12/24 V DC. If you have a GFCI-protected circuit on the dock and want to skip the battery, only ShoreMaster offers that. The general case is in AC vs DC boat lift motors, and panel sizing is in solar boat lift chargers.

4. Bolted frame vs welded frame

ShoreStation's hydraulic lift arrives as a kit. Its 22-page assembly manual bolts legs, side frames and cradle tubes together with stainless bolts and brass lock nuts. Lifts from 8,000 lb up get galvanized steel cradle tubes; 4,000 to 6,000 lb lifts get aluminum ones. ShoreMaster's frames are welded aluminum with "reinforced through-bolted connections," and it says welded seams cut down on bolt checks. No published test compares the two for strength. The real difference is upkeep: a bolted frame has more fasteners to check.

5. The warranties read differently

Both give 15 years on the frame for home use. After that they part.

  • Cables: ShoreStation's FAQ promises 15 years "on the cables and structure." ShoreMaster's vertical hydraulic page says 12 years on cables. Its cantilever hydraulic has no cables to cover.
  • Labor: ShoreMaster's written warranty (revision 08-2020) splits parts from labor. The lift frame gets 15 years of parts but 3 years of labor. The hydraulic ram and pump get 3 years of parts and 2 of labor. Other components get 2 years of parts and 1 of labor, and the LiftBoss Gen 6 motor carries 3 years. A dealer's copy of ShoreStation's terms adds a 2-year basic warranty that covers parts and labor on every part Midwest supplies.
  • Canopies: ShoreStation sells REVOLUTION and Legacy covers and a ShoreScreen power curtain, with a 5-year fabric warranty that is pro-rated after year two. ShoreMaster offers two frame styles and three fabrics, and its covers carry 5 years pro-rated. Fabric choices are compared in boat lift canopies.
  • Salt water: ShoreMaster drops every lift item to 1 year in brackish or salt water, or in any commercial use, and requires anodes.
  • Resale: ShoreMaster's warranty "is not transferrable or assignable." It ends when the first owner sells.

Some dealer pages still show an older ShoreStation term of 10 years on the frame. ShoreStation's own FAQ now says 15. Ask the dealer for the current written document before you sign. What to look for in any lift warranty is in boat lift warranties.

6. Width and depth limits

ShoreStation lists a 144 in inside width on its 10,000 and 15,000 lb hydraulic lifts. ShoreMaster's widest is 132 in. That 12 in matters for wide wake boats and tritoons.

Travel favors ShoreMaster at most sizes. Its cable and vertical hydraulic lifts move 66 to 70 in. ShoreStation's hydraulics move 48 in up to 5,000 lb, 54 in at 6,000 and 7,000, 64 in at 8,000 and 10,000, and 70 in only at 15,000. More travel lets a lift reach the boat at low water and still clear the waves at high water.

Depth is stated differently. ShoreMaster gives minimum water plus draft: 16 in plus draft for the TruLift cantilever, 5.75 to 11 in plus draft for the vertical hydraulic. It pitches the vertical hydraulic at 3 to 9 ft of water, though its FAQ on the same page says 3 to 7. ShoreStation lists a range for each size without mentioning draft. It runs from 11 in to 7 ft 7 in at 2,000 to 4,000 lb, up to 21 in to 10 ft 11 in at 15,000 lb. So ShoreStation publishes the deeper ceiling.

Worked example: one boat, two dealers

Worked example: a 6,300 lb deck boat with no power on the dock

Take a deck boat that weighs 6,300 lb loaded, with a 102 in beam. Say the dock has no electric circuit, and the slip holds 4 to 5 ft of water through the season.

Size the lift. Add a 20% margin: 6,300 x 1.2 = 7,560 lb. That points to an 8,000 lb lift. The method is in boat lift capacity sizing.

The ShoreStation quote. The 8,000 lb hydraulic lift has a 132 in inside width and 64 in of travel. It lists water from 14 in to 9 ft 10 in. With a 102 in beam, 132 - 102 = 30 in of side room, or 15 in a side when centered. Its battery and solar panel cover the missing dock circuit.

The ShoreMaster quote. The DVS cable lift stops at 7,000 lb, below the 7,560 lb target, so it drops out. That leaves two hydraulics. The 8010 VHL vertical hydraulic is 120 in wide with 68 in of travel. The 801060 TRU cantilever is 120 in wide with 60 in of travel and no cables. Both give 120 - 102 = 18 in of side room, or 9 in a side. Both also run on a 12 V battery with solar.

What decides it. Not power, since all three run on a battery. Not depth, since 4 to 5 ft sits inside every listed range. It comes down to three questions. Do you want cables at all? Do you want 15 in or 9 in a side when docking in a crosswind? And might you sell the house soon, given that ShoreMaster's warranty does not pass to the next owner?

Which to buy: a rule by depth, weight and dock power

Run your numbers through these rulings in order. Each one comes from the specs above.

ShoreStation or ShoreMaster: which the published specs favor
Your situationLean towardWhy
Loaded boat plus margin under 4,000 lb, manual lift is fineEitherBoth sell manual cable lifts in this range at 108 or 120 in
4,000 to 7,000 lb and you want a cable winchShoreMasterShoreStation lists manual lifts only to 4,000 lb
AC circuit on the dock and you want no batteryShoreMaster cable lift with a 120 V LiftBossShoreStation hydraulics use AC only to charge the battery
No power at the dockEitherBoth brands' hydraulics run on a battery with solar charging
Beam needs more than 132 in of inside widthShoreStationOnly ShoreStation lists 144 in (10,000 and 15,000 lb)
You want no lift cables at allShoreMaster cantilever hydraulicIts page states no cables and no pulleys; ShoreStation's hydraulics pull cables
Water deeper than about 9 ft at the liftShoreStationIts 8,000 lb and larger lifts list up to 9 ft 10 in and 10 ft 11 in; ShoreMaster pitches 3 to 9 ft
You may sell the property within the warranty yearsAsk ShoreStation's dealer about transferShoreMaster's warranty is not transferable
Brackish or salt waterNeither by defaultShoreMaster cuts coverage to 1 year there; see tidal and saltwater installations

If two rows point different ways, the weight and width rows win. A lift that cannot carry or fit the boat is the wrong lift, whatever the warranty says. Check depth at your lowest water with the water depth calculator.

Dealers and who owns each brand

ShoreStation is made by Midwest Industries, Inc. of Ida Grove, Iowa, which dates the brand to 1959. It warns that buying through eBay, Craigslist or other unauthorized outlets "may result in a voided warranty."

ShoreMaster, LLC is based in Fergus Falls, Minnesota. It is part of Waterfront Brands, with HydroHoist (joined 2019), Neptune Boat Lifts (2020) and Tide Tamer (2021). Neither brand publishes a dealer count.

Both brands also sell docks, so a dealer usually carries one brand's whole system, and the dealer choice becomes the brand choice. A nearby dealer who stocks cables and battery boxes is worth more than a spec-sheet edge, as argued in how to compare boat lift brands. If the other quote is from a Hewitt dealer, the same ShoreStation figures are set against Hewitt's in Hewitt vs ShoreStation. The brand profiles for ShoreStation and ShoreMaster cover used-lift checks and dealer questions.

What this comparison does not cover

It compares free-standing boat lifts on fresh water. PWC lifts, piling hoists, floating lifts and docks are left out. ShoreMaster lists a 1,200 lb PWC lift, but ShoreStation's PWC line was not checked, so there is no fair pair to set side by side. Prices are not given, because neither brand publishes them. Capacity ratings are the makers' own, and neither says how off-center loads change them. ShoreStation's aluminum lift warranty PDF would not load in November 2026, so its 2-year basic term comes from a dealer's copy. Get the current warranty in writing, and confirm width, travel and depth range on the quote itself. Hydraulic fluid differs between the brands too, and that is covered in what hydraulic fluid a boat lift uses.

Safety: never stand or work under a raised boat, on either brand. Any dock circuit, even one that only feeds a battery charger, belongs to a licensed electrician with GFCI protection. Faulty dock wiring can cause electric shock drowning; the rules are in boat lift electrical.

Frequently asked questions

Is ShoreStation or ShoreMaster better?

Neither is better across the board. ShoreStation lists wider hydraulic lifts (144 in) and a 15-year cable warranty, and its hydraulics need no dock circuit. ShoreMaster offers a cable lift to 7,000 lb with an AC motor option, plus a hydraulic lift with no cables. Match the lift to your boat weight, beam and dock power, then pick the closer dealer.

Do ShoreStation hydraulic lifts have cables?

Yes. The cylinder sits inside a lift tube and pulls stainless cables that run over pulleys to the cradle. ShoreStation calls them cables that are pulled rather than wound, since there is no drum. The cables carry a 15-year warranty. If you want a lift with no cables at all, ShoreMaster's cantilever hydraulic line is built that way.

Can a ShoreStation hydraulic lift run on AC power?

Not directly in the current line. ShoreStation describes its hydraulics as a DC system that removes the need for an AC circuit on the dock. The pump runs from a 12 V or 24 V battery. AC can still be used to charge that battery through a Battery Tender plugged into a 110 V outlet near the lift.

Is the ShoreMaster warranty transferable?

No. ShoreMaster's limited warranty, revision 08-2020, says it covers the original purchasing consumer and "is not transferrable or assignable." If you buy a used ShoreMaster lift, or sell your house with one in the water, the factory warranty does not move with it. Claims must reach a dealer in writing within 15 days of finding the defect.

Sources and further reading

  • ShoreStation, Boat Lift Capacity Models: hydraulic and manual capacities, inside widths, travel, water range (https://shorestation.azurewebsites.net/free-standing-boat-lifts/boat-lifts/capacity-models)
  • ShoreStation, Power Systems: DC operation, no AC circuit, pump box above water, cables pulled not wound, 15-year cable warranty (https://shorestation.azurewebsites.net/BoatLifts/powersystems)
  • ShoreStation, Lift Options: DC battery with solar or Battery Tender, GAR-MAX bushings, canopy covers (https://shorestation.azurewebsites.net/free-standing-boat-lifts/boat-lifts/lift-options)
  • ShoreStation, Free-Standing Boat Lift FAQs: 15-year warranty on cables and structure, 6 to 8 cycles per charge, battery life (https://shorestation.azurewebsites.net/free-standing-boat-lifts/faqs)
  • ShoreStation, Hydraulic Boat Lift Assembly Instructions 0004205, Rev 2.7, 3/13/2018: bolted frame, steel cradle tubes from 8,000 lb, cylinder in lift tube, 12 and 24 V pumps, Battery Tender HA0083/HA0084, solar HA0110/HA0135, upper limit switch (https://www.boatliftanddock.com/MediaStorage/Product/Documents/Document/3708_20201124151901766.pdf)
  • ShoreStation, Legacy and Revolution Canopy Warranty 0003624, Rev B 09/17/2018 (https://www.boatliftanddock.com/MediaStorage/Product/Documents/Document/3153_20201210163137620.pdf)
  • ShoreStation, Service and warranty pages: Midwest Industries, Ida Grove, unauthorized outlets (https://shorestation.azurewebsites.net/service and https://shorestation.com/service/warranty-info)
  • O'Donnell's Docks (ShoreStation dealer), ShoreStation Freestanding Boat Lift: 2-year basic limited warranty wording (https://odonnellsdocks.com/shorestation-boat-lift/)
  • ShoreMaster, Boat Lift Models overview: capacities, travel and widths by lift type, PWC lift (https://www.shoremaster.com/lifts/lift-models/)
  • ShoreMaster, Hydraulic Lifts: cantilever spec table, no cables or pulleys, 1 in per second, 12 V group 27 battery, 15-year frame (https://www.shoremaster.com/lifts/lift-models/hydraulic-lifts/)
  • ShoreMaster, Vertical Hydraulic Boat Lifts: spec table, 12-year cables, battery spec, no limit switch, depth range (https://www.shoremaster.com/boat-lifts/lift-models/vertical-hydraulic-lift/)
  • ShoreMaster, Vertical Lifts (DVS): spec table, brass sheaves, stainless cables, welded frame (https://www.shoremaster.com/boat-lifts/lift-models/vertical-lifts/)
  • ShoreMaster, Boat Lift Motors: LiftBoss Gen 5 and Gen 6, 120 V AC or 12/24 V DC, integrated motor on the 7,000 lb lift (https://www.shoremaster.com/lifts/boat-lift-motors/)
  • ShoreMaster, Limited Product Warranty, revision 08-2020 (https://stshoremasterprod.blob.core.windows.net/media/2342/shoremaster-limited-warranty-082020.pdf)
  • ShoreMaster, About ShoreMaster: Fergus Falls, Waterfront Brands, dealer network (https://www.shoremaster.com/about-shoremaster/)